1. Note

①Do Not Mix Batteries

②Do Not insert battery wrong side round

③Do Not insert battery wrong side round

2. Product Specification

Product Name: Navi1600 Smart Front Light

Dimension: L:112mm W:54mm H:34mm (See Fig.1)

Fig. 1

Navi1600 comes with a motion sensor and light sensor. The motion sensor allows the Navi1600 to detect if the bike is moving and turning on/off the light automatically.The integrated light sensor use to control the light power in Full-Auto Mode.

Operation Mode	Manual/Semi-Auto/Full-Auto
Battery	2x3350mAh rechargeable Lithium-ion battery
Run Time	Low Beam or High Beam only（One LED） 17.2hrs@200Lm, 8.2hrs@370Lm, 5.8hrs@570lm, 3.6hrs@800Lm Low Beam And High Beam(Two LED) 8.6hrs@400Lm, 4.1hrs@740Lm, 2.9hrs@1140lm, 1.8hrs@1600Lm
Weight	238g
Color	Black
Waterproof	IPx6
Input	5Vdc 2.1A(max)
Output	5Vdc 2.4A(max)

Fig. 3

Refer to Fig. 3, The name of the LED indicators and buttons are defined as below:

①High beam/ Low beam indicator ②Battery State③High/Low Beam Control

④Auto Mode indicator⑤Power Button⑥USB Type A Output

⑦USB Type C Input/Output ⑧Rubber Seal ⑨Light Sensor

3. Package Content

4. Operation and functionality

Button & Operation

Button	Operation	Function
Power Button⑤	Single Click	Change the output power or turn on the light
	Double Click	Switch between Auto mode and manual mode
	Press down > 1s	Switch off *

High/Low Beam Button③	Single Click	Switch Between High Beam and Low Beam

Table. 2 Button and function

Note:*When operating in Full-Auto or Semi-Auto mode the light will be turn on again if motion is detected .

Operation mode

The Navi1600 supports three operation modes which can switch between them by double click the power button as show below:

Auto/Manual mode

In FullAuto or Semi-Auto Mode, the Navi1600 will automatically turning on/off if the following conditions are met:

Note：*Use the Power Button to turn on/off the light in “Manual mode”

** Indicator ④ in Fig. 3 will start to flash or turn on

5. Charge the Battery/Portable Charger

Fig. 3

Charge the battery

When battery is running low, the battery indicators ② in Fig. 3 start flashing. To charge the battery, open the rubber seal ⑧ as in Fig. 3 and connect the USB cable to the USB Type C connector. Battery will be fully charge in about 2~3 hours. The four battery indicators ② will turn on solid when charge completed.

Portable Charger

The Navi1600 can acts as a portable Charger. The USB Type A(Fig.3⑥) and USB Type C(Fig.3⑦) terminals are able to deliver 5V 2.4A (max) in total.

Replace the battery

Remove the four screws from the back of Navi1600 as shown in Fig. 5 then the battery can be removed and replaced with full charged batteries.

Fig. 5

6. Installation

Handlebar mount:

As shown in Fig. 4, Mount the handlebar bracket ① to the handlebar and slide in the Navi1600 from the front ②.

Cycle Computer Mount (GoPro Adaptor)

Rotate the battery cartridge 180° and tighten the screws as Fig. 5.

As shown in Fig. 6, install the GoPro adaptor ① to a standard cycle computer bracket (with GoPro mount) and slide in the Navi1600 ② .

7. Warranty

The product is covered by a one year warranty.

Navi1600 User Manual